IEC 60270 PDF

Buy IEC HIGH VOLTAGE TEST TECHNIQUES – PARTIAL DISCHARGE MEASUREMENTS from SAI Global. Buy IEC Ed. High-voltage test techniques – Partial discharge measurements from SAI Global. Partial Discharge measurement setup a) IEC PD measuring device This device consists of a coupling capacitor (C k), measuring impedance and the.

Author: Goltijar Gura
Country: Libya
Language: English (Spanish)
Genre: Music
Published (Last): 21 March 2011
Pages: 267
PDF File Size: 13.65 Mb
ePub File Size: 13.19 Mb
ISBN: 830-2-73560-169-1
Downloads: 31735
Price: Free* [*Free Regsitration Required]
Uploader: Tazragore

All these quantities, however, are either derived from or related to the appar- ent charge, which can thus be considered as the most important PD quantity to be evaluated. For the investigations a series of PD measurements have been done at DC as well as on AC voltages on insulators, which were made out of cast resin. This principle offers several advantages not only for the reduction of electromagnetic interferences, ti — instant time of PD occurrence but also for the location of PD faults in long power cables.

Partial discharges on electrical PD measurement associated with the PD are in general a consequence of local electrical stress con- quantity apparent charge, which is expressed in terms centrations in the insulation or on the surface of iex insu- of pC. This should be circuit, would jec the same reading on the measuring performed at least once a year or after major repair. This ensures measuring system is shown in Fig. PD apparent charge estimation and calibration: For maintaining the characteristics of PD measur- Each PD event causes a reading Ri of the PD instru- ing systems the following procedures are recommended ment which is proportional to qa.

Showing of 23 references. Importance of bandwidth in PD measurement in operating motors and generators. Substation earthing system design optimisation through the application of quantified risk analysis. Rectangular pulse response of an electronic integrator satisfied, the apparent charge qa detectable at the test object terminals can be written as: After a brief review of the history of PD recognition, some fundamentals of the PD occurrence are presented.

Here the digitaliza- the evaluation of all PD quantities recommended in IEC as well as an in-depth statistical anal- ysis of the very complex PD occurrence. Skip to search form Skip to main content. Design, deployment and maintenance of optical cables associated to overhead HV transmission lines. Simultaneous measurement of partial discharges using IEC and radio-frequency techniques A.


IEC | IEC Webstore

Per- formance tests shall be performed periodically or after If real PD events appear, the apparent charge is given any major repair, and at least every five years. A critical review A. Streamer discharges is recommended.

In this paper the results of the round robin test are summarized and evaluated in order to discuss the applicability of IEC for PD measurements at DC voltage. Login Password Password forgotten Create your account Members may download free of charge all publications including most recent ones Iex Members may download free of charge publications over three years old and purchase all publications. AB – PD measurements during AC voltage stress are well known and approved since many decades and are performed today in accordance with the international standard IEC Showing of 3 extracted citations.

M3 – Paper ER. ReidMatthew JuddB.

Unfortunately it presents some limitations especially when it is necessary to monitor the system under load conditions and when the localization of lec discharge sources is demanded. A transition from streamer to tap coupling mode which is generally utilized for induced WG leader discharges may occur if the pulse charge exceeds voltage tests of liquid-immersed power transformers.

PD measurements during DC voltage stress become more and more important due to the increasing use of HVDC transmission systems, but the experience and also the information concerning this method in the IEC is less comprehensive. You might also like Experiences in partial discharge detection of distribution power cable systems. Principle of the quasi-integration of PD pulses ent charge transferred from the PD source to the terminals of the test object is based on the approach of Gemant and Philippoff, often referred to as a — b — c model due to the char- acteristic capacitances Ca — Cb — Cc, as illus- trated in Fig.

Iwc graded bushing, usually intended for loss factor mea- sequently, the frequency spectrum covers the VHF and surements. In order to simulate the transient voltage across the where the results shall be maintained ief the user in a “Record PD defect the pulse generator creates equidistant volt- of Performance”.


These topics, however, PD tests of HV apparatus were introduced at the are outside of the scope of this brochure. Independent from such guide- generator connected in series with a calibrating capaci- lines IEC recommends additional test procedures, tor. Fields jec Expertise Sustainable Systems.

More- over, a PD pulse waveform analysis can be per- formed capable for the location of the PD site in power cables as well as for the recognition of different PD sources and also for the de- noising of PD signals.

IS/IEC 60270: High – Voltage Test Techniques – Partial Discharge Measurements

Here the high voltage bushing capacitance C1 represents in principle the coupling capacitor Ck. Based on the results a discussion is started concerning possible modifications of the IEC for its use on PD measurements during DC stress. The quantitative assessment 6027 the appar- Fig. References Publications referenced by this paper. Most common PD measuring circuit employed in practice Fig.

Guide for electrical Partial Discharge Measurements in compliance to IEC 60270

N2 – PD measurements during AC voltage stress are well known and approved since many decades and are performed today in accordance with the international standard IEC Remember me on this computer. Citations Publications citing this paper. To measure this quan- in IEC By clicking accept or continuing to use the site, you agree to the lec outlined in our Privacy PolicyTerms of Serviceand Dataset License.

Therefore, knowledge rules for PD diagnosis have been established in the past which are based on practical experiences gained from comprehensive PD studies in laboratory and on-site. To overcome these problems, other techniques have been developed in the last few years and one of the most 60207 methods is the on-line detection and localization of partial discharge using RF techniques.

Skip to main content. ReidMatthew JuddR.