CSWIP (WELDING INSPECTOR) MULTIPLE CHOICE QUESTIONS 1. When “ H2 control” is specified for a manual metal arc welding project, the electrode. MMA. 1. Which welding process is considered to be the most versatile? 2. (a) SAW (b) TIG (c) MIG / MAG (d) MMA One of the advantages of a multi-pass MMA . MULTICHOICE PAPER ONE ‘hydrogen control’ is specified for a manual metal arc welding project the electrode would normally be: a. Cellulose.
|Published (Last):||25 May 2014|
|PDF File Size:||10.75 Mb|
|ePub File Size:||16.87 Mb|
|Price:||Free* [*Free Regsitration Required]|
The defect repaired was lack of inter-penetration and it had been excavated with a disc grinder prior to repair.
In general it is not easy to mechanise the MMA welding process because: An essential anxwers may: Which of the following statements is true? So it can be ready for painting b. Removing ad is a premium feature.
The use of cobalt as an isotope would generally be used on: The important point of high temperature steels is that: Welds made with high heat inputs show a reduction in one of the following properties: Heavy porosity on the surface of some MMA welds made on a construction site is most likely to be caused by:. Our support team is online round-the-clock.
CSWIP 3.1 Multiple Choice Paper 1
All questions 5 questions 6 questions 7 questions 8 questions 9 questions 10 questions 11 questions 12 questions 13 questions 14 questions 15 questions 16 questions 17 questions 18 questions 19 questions 20 questions 21 questions 22 questions 23 questions 24 questions 25 questions 26 questions 27 questions 28 questions 29 questions 30 questions.
The steel composition in a structural contract is changed form 0. What is the leg ansswers of a fillet weld?
Lamellar tearing affects all joint types What is Lamellar tearing? Tensile strength of the weld b. Being rough and torn d. What change will occur on the HAZ during heating of metal caused by welding?
CSWIP Multiple Choice Questions Quiz – ProProfs Quiz
You notice manual metal arc electrodes, stripped of flux, are being used as filler wire for TIG welding. Less than 5ml per g of weld metal deposited b. Lamellar tearing has occurred in a steel fabrication. Three essential factors for producing fusion weld are melting, removal of surface oxide from the joint surfaces and elimination of atmosphere from the region of the arc.
Go to My Dashboard. Non-planar defects associated with a weld: Which of the following processes joints metals plastically: The main reason degreasing agents should always be dried from metals prior to welding, is because they are likely to: Email required Address never made public.
CSWIP Multiple Choice Paper 1 – ProProfs Quiz
To find out more, including how to control cookies, see here: Which of the following processes would be most prone to lack of fusion defects: The HAZ associated with a weld is: To find out more, including how to control cookies, see here: Planar defect are best described ansers What two functions in arc welding must be in equilibrium to enable a stable arc to be established?
Leave a Reply Cancel reply Xnd your comment here Technically, a code of practice is: When referring to MIG welding, the shielding gas could be: You can check out with Bit SSL encryption.
Notify me of new comments via email. Macroscopic examination requires any specimen to be inspected: Which of the following could cause root concavity? This is to influence: So, the Welding Inspector 3.
In gas welding, leftward welding is described in BS as: Cold lap in another term for: When welds have a depth to width ration of higher than 2: A repair has wnd made using MMA on a double V butt weld on a 10 m diameter tank. Flame cut preparation may, during welding, increase the likelihood of: A welder qualification test is to verify: What kind of steel is used for making filler rod? What would you investigate: In TIG welding the nozzle is usually made: The surface to be examined shall be free from all dirt, grease, lint, oil, scale or slag.
Welding a steel plate of a CE of 0.