AN1020-25 USER MANUAL PDF

ptcl router manual. An User Manual Router All materials on our website are shared by users. If you have any questions about. USER MANUAL. TestClick ADSL BER Test to perform a bit error rate (25 26Note: If the BER reaches e-5, you cannot access the Internet. Find the default login, username, password, and ip address for your Fiber Home AN router. You will need to know then when you get a new router.

Author: Samukasa Akinozahn
Country: Luxembourg
Language: English (Spanish)
Genre: Technology
Published (Last): 16 March 2013
Pages: 161
PDF File Size: 11.72 Mb
ePub File Size: 11.41 Mb
ISBN: 168-9-16225-732-4
Downloads: 60682
Price: Free* [*Free Regsitration Required]
Uploader: Faular

Post on Nov 15 views.

An1020-25 User Manual Router

The frequency of ADSL signal is higher than that of voice, so voice and ADSL signal can coexist in one line by using a splitter to insulate each from the other. ADSL data transfer on the asymmetry way.

The upload speed is up to 1Mbps and download speed is up to 8Mbps. It is an ideal device for broadband access. These improvements are mainly concerned with long distance, anti-line-loss, anti-noise, etc.

Therefore, Internet applications such as synchronous transmission of multi video stream, online games and huge capacity of downloading files are made possible. Connected to ADSL port of the splitter or on the phone jack wall. To be connected to a PC network card by a network cable, also can use a crossover cable to connect to Hub, Switch or Router. To turn on or turn off the power. mxnual

Web-based configuration and monitoring. Supports up to 8 PVCs. Plug in the power cord, and turn on the power. The Subnet Mask is: Press Enter key then the entry dialog box will pop up as Figure 2. Only need to use the third party dial-up software to connect the Internet. For detail configuration information, please check the following configuration guide. In the Connections page, the default configuration of the modem supports seven PVCs.

Delete an existing Internet connection. Modify an existing Internet connection. After the deletion, the page shown in the following figure appears. It supports eight characters at most.

Its msnual value is from 0 to Its valid value is from 32 to When the network is congested, the UBR cell is dropped an102025 communication traffic is at a fairly low level. Its peak cell rate range is from 0 to Constant bit rate CBR is a coding mode. It is adapted maual strict requirement to delay and quality of data packets transmission. The sustainable cell rate range is from 1 toan020-25 the maximum burst size range is from 0 to Real-time variable bit rate Real-time VBR is adapted for real time with high requirement.

  EN MEMORIA DE PAULINA BIOY CASARES PDF

After proper modifications, click Next and the following page appears. In this page, you can modify Internet connection protocol and encapsulation type. Use the following IP address: Select it to enable the An0120-25 functions of the modem. If you do not manul to enable NAT and want the user of the modem to access the Internet normally, you must add a route on the uplink equipment.

Otherwise, the access to the Internet fails. Normally, it is required to enable NAT.

Add a default route in the routing table. Normally, it must be checked, or you have to add a default route manually. Select a proper PPP connection mode.

Enter the correct user name provided by your ISP. Enter the correct password provided by your ISP. Confirm the correct password provided usrr your ISP. Select a PPP connection mode according to your practice.

User Manual Guide – AN – [PDF Document]

After the device is powered on, the system performs PPP dial-up automatically. After the device is powered on, the PPP dial-up performs automatically.

If the device does not detect the flow of the user continuously within the preset minutes, the device automatically stops the PPP connection. Once the device detects the data flow for example, accessing the web pageit restarts the PPP for dial-up. If the device does not detect the data-flow of the user continuously within the preset minutes, the device automatically releases the PPP connection.

The difference between manually connect and dial on demand is that you must start a PPP connection manually again if you select manually connect. Enter the waiting time in the field. In this page, you can confirm the modification. When you are sure that your configuration is correct, click Apply.

How to Login to the FiberHome AN

The page shown in the following figure appears. Enter from the services provided by the ISP. It may not fill. When you are sure manua the configuration is correct, click Apply. Select use the following IP address, and then you can enter the IP address of the gateway. Click Next and the following page appears. Choose the connection protocol of the RFC Routed. At most we can have eight connections. In this page, you can configure an10200-25 local network. The default is The subnet mask of the IP address.

  KEIL UV2 PDF

FiberHome AN1020-25 User Manual

The default one is By default, it is not selected. Select it if you need to configure the virtual IP address and subnet mask. The default of maximum transmission unit is Enter the required parameters and click Apply to take it effect.

After the modification, the maximum transmission unit can reach The configuration steps are shown below: In this page, you can set the status of the DHCP server. Select it to enable the DHCP server function. By default, DHCP server is enabled. In this page, you can modify the DHCP server settings. The maximum value which default lease time can be set to. The unit value is set in second. By default, it is seconds 24 hour. After the preset time, the lease IP is released.

By default, it is seconds 12 hour. The user can configure these addresses through the Local Network page. Configuration of administrators password and users password When logging on the setting page of ADSL Modem, the system requires user name and password to verify for permission.

The default administrators account is admin and the default password for this account is admin.

The user, through the user configuration tab on page System, can change the passwords. Then wn1020-25 will be able to log on with the default username and password. The Gateway can be seen as a simple two-port HUB.

,anual using USB Interface, you must install the drivers. It has all the functions of a real network card, and it makes installation more easily.

The following shows the steps for Windows, the installation, configuration and un-installation of Windows98 or WindowsXP are similar to this. Open the Modem, and connect the USB port.

Then double click Setup. A new dialog box will show you a figure 7. Click Accept to continue. A new box will show whether you want to reboot the computer.

Choose No, I will reboot the computer later,Figure 7. As shown in figure 7. It will ask you to clickYesto confirm deletion. User can also change its configuration for special reason. Make sure the connection of power supply is good.